View NCP584HSN30T1G_8187345.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2010 february, 2010 ? rev. 14 1 publication order number: ncp584/d ncp584 tri-mode 200 ma cmos ldo regulator with enable the ncp584 series of low drop out regulators are designed for portable battery powered applications which require precise output voltage accuracy, low quiescent current, and high ripple rejection. these devices feature an enable function which lowers current consumption significantly and are offered in the sot23 ? 5 package. this series of devices have three modes. chip enable (ce mode), fast transient mode (ft mode), and low power mode (lp mode). both the ft and lp mode are utilized via the eco pin. features ? tri ? mode operation ? low dropout voltage of 400 mv at 200 ma, output voltage = 0.9 v 300 mv at 200 ma, output voltage = 1.2 v 200 mv at 200 ma, output voltage = 1.8 v ? excellent line regulation of 0.05%/v (0.10% lp mode) ? excellent load regulation of 10 mv (20 mv ft mode) ? high output voltage accuracy of 2% ( 3% lp mode) ? ultra ? low iq current of: 3.5 a (lp mode, output voltage 1.5 v) 40 a (ft mode) ? very low shutdown current of 0.1 a ? excellent power supply rejection ratio of 75 db at f = 1.0 khz ? low temperature drift coefficient on the output voltage of 100 ppm/ c ? fold back protection circuit ? input voltage up to 6.5 v ? these are pb ? free devices typical applications ? portable equipment ? hand ? held instrumentation ? camcorders and cameras figure 1. simplified block diagram for active low figure 2. simplified block diagram for active high + - v in v ref current limit ce v out gnd eco + - v in v ref current limit ce v out gnd eco sot23 ? 5 sn suffix case 1212 http://onsemi.com marking diagram see detailed ordering and shipping information in the package dimensions section on page 13 of this data sheet. ordering information 1 5 xxxtt 1 5 xxx = specific device code tt = traceability information *additional voltage options may be available between 0.8 v and 3.3 v in 100 mv steps.
ncp584 http://onsemi.com 2 pin function description sot23 ? 5 pin name description 1 v in power supply input voltage. 2 gnd power supply ground. 3 ce or ce chip enable pin. 4 eco mode alternative pin. (v eco = v in for ft mode; v eco = gnd for lp mode) 5 v out regulated output voltage. maximum ratings rating symbol value unit input v oltage v in 6.5 v input voltage (ce or ce pin) v ce ? 0.3 to v in +0.3 v input voltage (eco pin) v eco ? 0.3 to v in +0.3 v output v oltage v out ? 0.3 to v in +0.3 v output current i out 250 ma power dissipation p d 250 mw esd capability, human body model, c = 100 pf, r = 1.5 k esd hbm 1000 v esd capability, machine model, c = 200 pf, r = 0 esd mm 150 v operating ambient temperature range t a ? 40 to +85 c maximum junction t emperature t j(max) 125 c storage temperature range t stg ? 55 to +150 c stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability.
ncp584 http://onsemi.com 3 electrical characteristics (v in = v out + 1.0 v, t a = 25 c, unless otherwise noted.) characteristic symbol min typ max unit input v oltage v in 1.4 ? 6.0 v output voltage (1.0 a i out 30 ma) v eco = v in v eco = gnd v out v out x 0.980 v out x 0.970 ? ? v out x 1.020 v out x 1.030 v line regulation (i out = 30 ma, v out + 0.5 v v in 6.0 v) ft mode v eco = v in lp mode v eco = gnd reg line ? ? 0.05 0.10 0.20 0.30 %/v load regulation ft mode (1.0 ma i out 200 ma), v eco = v in lp mode (1.0 ma i out 100 ma), v eco = gnd reg load ? ? 20 10 40 40 mv dropout voltage (i out = 200 ma) v out = 0.9 v 1.2 v v out 1.5 v 1.8 v v out 2.5 v 2.6 v v out 3.3 v v do ? ? ? ? 0.40 0.30 0.20 0.10 0.70 0.50 0.30 0.20 v quiescent current (i out = 0 ma) ft mode, v eco = v in lp mode, v eco = gnd v out 1.5 v v out 1.8 v iq ? ? ? 40 3.5 4.5 70 6.0 8.0 a output current (v in ? v out = 0.5 v) v in 1.5 v, v out = 0.9 v i out 200 ? ? ma shutdown current (v ce = v in ) i sd ? 0.1 1.0 a output short circuit current (v out = 0 v) i lim ? 50 ? ma enable input threshold v oltage high low vth enh vth enl 1.0 0 ? ? v in 0.3 v ripple rejection (i out = 30 ma, v out = 0.9 v, v in ? v out = 1.0 v) f = 120 hz f = 1.0 khz f = 10 khz rr ? ? ? 75 75 65 ? ? ? db output noise voltage (bw = 10 hz to 100 khz vn ? 30 ? vrms output voltage temperature coef ficient (i out = 30 ma, ? 40 c t a 85 c) v out / t ? 100 ? ppm/ c
ncp584 http://onsemi.com 4 typical characteristics figure 3. output voltage vs. output current figure 4. output voltage vs. output current 0 100 300 output current i out (ma) output voltage v out (v) 400 v out = v out nominal eco = h v in = v out nominal +2.0 v 200 0 100 300 output current i out (ma) output voltage v out (v) 400 200 v in = v out nominal + v do (max) v out = v out nominal eco = l v in = v out nominal +2.0 v v in = v out nominal + v do (max) figure 5. output voltage vs. input voltage figure 6. output voltage vs. input voltage 0.8 0.1 2.1 3.1 4.1 input voltage v in (v) output voltage v out (v) i out = 1.0 ma 5.1 0.7 0.6 0.5 0.4 0.3 0.2 0.1 i out = 30 ma i out = 50 ma 6.1 v out = 0.9 v eco = h 1.1 1.0 0.9 1.1 0.8 0.1 2.1 3.1 4.1 input voltage v in (v) output voltage v out (v) i out = 1.0 ma 5.1 0.7 0.6 0.5 0.4 0.3 0.2 0.1 i out = 30 ma i out = 50 ma 6.1 v out = 0.9 v eco = l 1.1 1.0 0.9 1.1 1.9 0.3 2.3 3.3 4.3 input voltage v in (v) output voltage v out (v) i out = 1.0 ma 5.3 1.5 1.3 1.1 0.9 0.7 0.5 0.3 i out = 30 ma i out = 50 ma 6.3 v out = 1.8 v eco = l 1.3 1.7 figure 7. output voltage vs. input voltage figure 8. output voltage vs. input voltage 1.9 0.3 2.3 3.3 4.3 input voltage v in (v) output voltage v out (v) i out = 1.0 ma 5.3 1.5 1.3 1.1 0.9 0.7 0.5 0.3 i out = 30 ma i out = 50 ma 6.3 v out = 1.8 v eco = h 1.3 1.7 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 1.0 0.9
ncp584 http://onsemi.com 5 typical characteristics 1.1 2.1 3.1 4.1 input voltage v in (v) quiescent current, iq ( a) 5.1 6.1 70 60 50 40 30 20 10 0 0.1 figure 9. quiescent current vs. input voltage v out = 0.9 v eco = h 1.3 2.3 3.3 4.3 input voltage v in (v) 5.3 6.3 70 60 50 40 30 20 10 0 0.3 v out = 1.8 v eco = h figure 10. quiescent current vs. input voltage 1.1 2.1 3.1 4.1 input voltage v in (v) 5.1 6.1 8 7 6 5 4 3 2 1 0 0.1 v out = 0.9 v eco = l figure 11. quiescent current vs. input voltage figure 12. quiescent current vs. input voltage 1.3 2.3 3.3 4.3 input voltage v in (v) supply current, i supply ( a) 5.3 6.3 8 7 6 5 4 3 2 1 0 0.3 v out = 1.8 v eco = l quiescent current, iq ( a) quiescent current, iq ( a) figure 13. output v oltage vs. temperature ? 25 0 25 50 temperature ( c) output voltage, v out (v) 100 0.93 0.92 0.91 0.90 0.89 0.88 0.87 ? 50 75 v out = 0.9 v eco = h figure 14. output v oltage vs. temperature ? 25 0 25 50 temperature ( c) output voltage, v out (v) 100 0.93 0.92 0.91 0.90 0.89 0.88 0.87 ? 50 75 v out = 0.9 v eco = l
ncp584 http://onsemi.com 6 typical characteristics figure 15. output v oltage vs. temperature ? 25 0 25 50 temperature ( c) output voltage, v out (v) 100 1.22 1.21 1.20 1.19 1.18 1.17 1.16 ? 50 1.23 75 v out = 1.2 v eco = h figure 16. output v oltage vs. temperature ? 25 0 25 50 temperature ( c) output voltage, v out (v) 100 1.22 1.21 1.20 1.19 1.18 1.17 1.16 ? 50 1.23 75 v out = 1.2 v eco = l figure 17. dropout v oltage vs. output current 25 50 75 100 output current i out (ma) dropout voltage, v do (v) 150 0.6 0.4 0.3 0.2 0.1 0.0 0 v out = 0.9 v eco = h 125 ? 40 c 85 c 25 c 200 175 0.5 25 50 75 100 output current i out (ma) dropout voltage, v do (v) 150 0.6 0.4 0.3 0.2 0.1 0.0 0 v out = 0.9 v eco = l 125 ? 40 c 85 c 25 c 200 175 0.5 figure 18. dropout v oltage vs. output current figure 19. dropout voltage vs. output current 25 50 75 100 output current i out (ma) dropout voltage, v do (v) 150 0.30 0.20 0.15 0.10 0.05 0.00 0 v out = 1.2 v eco = h 125 ? 40 c 85 c 25 c 200 175 0.25 0.40 0.35 25 50 75 100 output current i out (ma) dropout voltage, v do (v) 150 0.30 0.20 0.15 0.10 0.05 0.00 0 v out = 1.2 v eco = l 125 ? 40 c 85 c 25 c 200 175 0.25 0.40 0.35 figure 20. dropout v oltage vs. output current
ncp584 http://onsemi.com 7 typical characteristics figure 21. dropout v oltage vs. output current 25 50 75 100 output current i out (ma) dropout voltage, v do (v) 150 0.30 0.20 0.15 0.10 0.05 0.00 0 v out = 1.8 v eco = h 125 ? 40 c 85 c 25 c 200 175 0.25 25 50 75 100 output current i out (ma) dropout voltage, v do (v) 150 0.30 0.20 0.15 0.10 0.05 0.00 0 v out = 1.8 v eco = l 125 ? 40 c 85 c 25 c 200 175 0.25 figure 22. dropout v oltage vs. output current figure 23. ripple rejection vs. frequency figure 24. ripple rejection vs. frequency 90 1 10 frequency, f (khz) ripple rejection, rr (db) 100 80 70 60 50 40 30 20 10 0 0.1 90 1 10 frequency, f (khz) ripple rejection, rr (db) 100 80 70 60 50 40 30 20 10 0 0.1 i out = 1.0 ma i out = 30 ma i out = 1.0 ma i out = 30 ma i out = 50 ma v out = 0.9 v v in = 1.4 v + 0.2 v p ? p c out = 2.2 f, eco = h v out = 0.9 v v in = 1.4 v + 0.2 v p ? p c out = 2.2 f, eco = l figure 25. ripple rejection vs. frequency figure 26. ripple rejection vs. frequency 90 1 10 frequency, f (khz) ripple rejection, rr (db) 100 80 70 60 50 40 30 20 10 0 0.1 90 1 10 frequency, f (khz) ripple rejection, rr (db) 100 80 70 60 50 40 30 20 10 0 0.1 i out = 1.0 ma i out = 30 ma i out = 1.0 ma i out = 30 ma i out = 50 ma v out = 1.2 v v in = 2.2 v + 0.2 v p ? p c out = 2.2 f, eco = h v out = 1.2 v v in = 2.2 v + 0.2 v p ? p c out = 2.2 f, eco = l i out = 50 ma i out = 50 ma
ncp584 http://onsemi.com 8 typical characteristics 10 50 time, t ( s) output voltage, v out (0.02 v/div) 100 0 output v oltage input v oltage 20 60 30 70 40 80 90 input voltage, v in (1.0 v/div) 0.4 2.0 time, t (ms) 4.0 0.0 output v oltage input v oltage 0.8 2.4 1.2 2.8 1.6 3.2 3.6 input voltage, v in (1.0 v/div) eco = h, i out = 30 ma t r = t f = 5 s, c out = 1.0 f v out = v out nominal figure 27. input transient response eco = l, i out = 10 ma t r = t f = 5 s, c out = 1.0 f v out = v out nominal 10 50 time, t ( s) output voltage, v out (0.02 v/div) 100 0 output v oltage input v oltage 20 60 30 70 40 80 90 input voltage, v in (1.0 v/div) 0.4 2.0 time, t (ms) output voltage, v out (0.5 v/div) 4.0 0.0 output v oltage input v oltage 0.8 2.4 1.2 2.8 1.6 3.2 3.6 input voltage, v in (1.0 v/div) eco = h, i out = 30 ma t r = t f = 5 s, c out = 2.2 f v out = v out nominal eco = l, i out = 10 ma t r = t f = 5 s, c out = 2.2 f v out = v out nominal output voltage, v out (0.5 v/div) 10 50 time, t ( s) output voltage, v out (0.02 v/div) 100 0 output v oltage input v oltage 20 60 30 70 40 80 90 input voltage, v in (1.0 v/div) 0.4 2.0 time, t (ms) output voltage, v out (0.05 v/div) 4.0 0.0 output v oltage input v oltage 0.8 2.4 1.2 2.8 1.6 3.2 3.6 input voltage, v in (1.0 v/div) eco = h, i out = 30 ma t r = t f = 5 s, c out = 4.7 f v out = v out nominal eco = l, i out = 10 ma t r = t f = 5 s, c out = 4.7 f v out = v out nominal
ncp584 http://onsemi.com 9 typical characteristics 08 time, t ( s) output voltage, v out (0.1 v/div) 18 ? 2 output v oltage load current 210 412 61416 150 100 50 0 load current, i out (ma) eco = h, v in = v out nominal + 1.0 v c in = 1.0 f, c out = 1.0 f v out = v out nominal 1.0 5.0 time, t (ms) output voltage, v out (0.5 v/div) 0.0 output v oltage load current 2.0 6.0 3.0 7.0 4.0 20 0 load current, i out (ma) 10 eco = l, v in = v out nominal + 1.0 v c in = 1.0 f, c out = 1.0 f v out = v out nominal figure 28. load transient response 08 time, t ( s) output voltage, v out (0.1 v/div) 18 ? 2 output v oltage load current 210 412 61416 150 100 50 0 load current, i out (ma) eco = h, v in = v out nominal + 1.0 v c in = 1.0 f, c out = 2.2 f v out = v out nominal 1.0 5.0 time, t (ms) output voltage, v out (0.5 v/div) 0.0 output v oltage load current 2.0 6.0 3.0 7.0 4.0 20 0 load current, i out (ma) 10 eco = l, v in = v out nominal + 1.0 v c in = 1.0 f, c out = 2.2 f v out = v out nominal 08 time, t ( s) output voltage, v out (0.1 v/div) 18 ? 2 output v oltage load current 210 412 61416 150 100 50 0 load current, i out (ma) eco = h, v in = v out nominal + 1.0 v c in = 1.0 f, c out = 4.7 f v out = v out nominal 1.0 5.0 time, t (ms) output voltage, v out (0.5 v/div) 0.0 output v oltage load current 2.0 6.0 3.0 7.0 4.0 20 0 load current, i out (ma) 10 eco = l, v in = v out nominal + 1.0 v c in = 1.0 f, c out = 4.7 f v out = v out nominal
ncp584 http://onsemi.com 10 typical characteristics figure 29. turn ? on/off speed with ce pin (v out = 0.9 v) 20 time, t ( s) ce input voltage, v ce (v) 70 2.4 1.8 1.2 0.6 0.0 30 040 10 50 60 2.6 2.1 output voltage, v out (v) 0.6 0.1 i out = 200 ma v ce = 0 v to 1.8 v 1.6 1.1 figure 30. turn ? on/off speed with ce pin (v out = 1.2 v) eco = h, v in = 1.8 v, c in = 1.0 f, c out = 2.2 f 200 time, t ( s) ce input voltage, v ce (v) 700 2.4 1.8 1.2 0.6 0.0 300 0 400 100 500 600 2.6 2.1 output voltage, v out (v) 0.6 0.1 i out = 200 ma v ce = 0 v to 1.8 v 1.6 1.1 eco = l, v in = 1.8 v, c in = 1.0 f, c out = 2.2 f 20 time, t ( s) ce input voltage, v ce (v) 70 3.2 2.4 1.6 0.8 0.0 30 040 10 50 60 2.2 1.7 output voltage, v out (v) 0.2 ? 0.3 i out = 200 ma v ce = 0 v to 2.5 v 1.2 0.7 eco = h, v in = 2.5 v, c in = 1.0 f, c out = 2.2 f 200 time, t ( s) ce input voltage, v ce (v) 700 3.2 2.4 1.6 0.8 0.0 300 0 400 100 500 600 2.2 1.7 output voltage, v out (v) 0.2 ? 0.3 i out = 200 ma v ce = 0 v to 2.5 v 1.2 0.7 eco = l, v in = 2.5 v, c in = 1.0 f, c out = 2.2 f
ncp584 http://onsemi.com 11 0.2 1.0 time, t (ms) output voltage, v out (v) 2.0 0.95 0.94 0.93 0.92 0.91 0.90 0.89 0.0 v eco ? 0 v to 1.3 v i out = 200 ma 0.4 1.2 0.6 1.4 0.8 1.6 1.8 3.0 2.0 1.0 0.0 eco input voltage, eco ? in (v) 0.91 0.90 0.89 0.91 0.90 0.89 0.91 0.90 0.89 0.90 0.89 0.88 0.90 0.89 0.88 i out = 100 ma i out = 50 ma i out = 10 ma i out = 1 ma i out = 0 ma figure 31. output voltage at mode alternative point (c in = 1.0 f, c out = 2.2 f, 8.0 v, v out = 0.9 v)
ncp584 http://onsemi.com 12 application information input decoupling a 1.0 f tantalum capacitor is the recommended value to be connected between v in and gnd. for pcb layout considerations, the traces of v in and gnd should be sufficiently wide in order to minimize noise and prevent unstable operation. output decoupling it is recommended to use a 2.2 f or higher tantalum capacitor on the v out pin. for better performance, select a tantalum capacitor with low equivalent series resistance (esr). if you use a tantalum type capacitor with high esr value of this capacitor, output might be unstable. for a ceramic type capacitor it is recommended connection about 1 resistor in series for the stability of output voltage. the relation between output current of regulator and esr of an output capacitor is shown in figures 32 to 34. those charts show minimal value of esr for stable output voltage in fast transient mode. the minimal esr of an output ceramic capacitor in low power mode is 40 m for all output voltages. for pcb layout considerations, place the output capacitor close to the output pin and keep the leads short as possible. 0 50 100 150 200 250 300 350 400 450 0 20 40 60 80 100 120 140 160 180 200 output current (ma) esr (m ) figure 32. minimal esr of output ceramic capacitor vs. output current v out = 0.9 v v in = 3 v ft mode t a = 25 c c out = 1 f c out = 2.2 f 0 50 100 150 200 250 300 0 20 40 60 80 100 120 140 160 180 200 output current (ma) figure 33. minimal esr of output ceramic capacitor vs. output current esr (m ) c out = 1 f c out = 2.2 f v out = 1.2 v v in = 3 v ft mode t a = 25 c 0 5 10 15 20 25 30 35 40 45 0 25 50 75 100 125 150 175 200 output current (ma) figure 34. minimal esr of output ceramic capacitor vs. output current esr (m ) v out = 3.3 v v in = 5 v ft mode t a = 25 c c out = 1 f c out = 2.2 f
ncp584 http://onsemi.com 13 ordering information device output t ype / features nominal output v oltage marking package shipping ? ncp584hsn09t1g active high, lp and ft mode 0.9 109 sot23 ? 5 (pb ? free) 3000 / tape & reel ncp584hsn12t1g active high, lp and ft mode 1.2 112 sot23 ? 5 (pb ? free) 3000 / tape & reel ncp584hsn15t1g active high, lp and ft mode 1.5 115 sot23 ? 5 (pb ? free) 3000 / tape & reel ncp584hsn18t1g active high, lp and ft mode 1.8 118 sot23 ? 5 (pb ? free) 3000 / tape & reel ncp584hsn25t1g active high, lp and ft mode 2.5 125 sot23 ? 5 (pb ? free) 3000 / tape & reel ncp584hsn26t1g active high, lp and ft mode 2.6 126 sot23 ? 5 (pb ? free) 3000 / tape & reel ncp584hsn28t1g active high, lp and ft mode 2.8 128 sot23 ? 5 (pb ? free) 3000 / tape & reel NCP584HSN30T1G active high, lp and ft mode 3.0 130 sot23 ? 5 (pb ? free) 3000 / tape & reel ncp584hsn31t1g active high, lp and ft mode 3.1 131 sot23 ? 5 (pb ? free) 3000 / tape & reel ncp584hsn33t1g active high, lp and ft mode 3.3 133 sot23 ? 5 (pb ? free) 3000 / tape & reel ncp584lsn09t1g active low, lp and ft mode 0.9 009 sot23 ? 5 (pb ? free) 3000 / tape & reel ncp584lsn12t1g active low, lp and ft mode 1.2 012 sot23 ? 5 (pb ? free) 3000 / tape & reel ncp584lsn18t1g active low, lp and ft mode 1.8 018 sot23 ? 5 (pb ? free) 3000 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specification brochure, brd801 1/d. other voltages are available. consult your on semiconductor representative.
ncp584 http://onsemi.com 14 package dimensions sot23 ? 5 sn suffix case 1212 ? 01 issue o dim min max millimeters a1 0.00 0.10 a2 1.00 1.30 b 0.30 0.50 c 0.10 0.25 d 2.80 3.00 e 2.50 3.10 e1 1.50 1.80 e 0.95 bsc e1 1.90 bsc l l1 0.45 0.75 notes: 1. dimensions are in millimeters. 2. interpret dimensions and tolerances per asme y14.5m, 1994. 3. datum c is a seating plane. a 1 5 23 4 d e1 b l1 e e e1 c m 0.10 c s b s a b 5x a2 a1 s 0.05 c l 0.20 --- 0.7 0.028 1.0 0.039 mm inches scale 10:1 0.95 0.037 2.4 0.094 1.9 0.074 *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting t echniques reference manual, solderrm/d. soldering footprint* on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, in cluding without limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different a pplications and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical e xperts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc prod uct could create a s ituation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indem nify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney f ees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was neglig ent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5773 ? 3850 ncp584/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loc a sales representative

▲Up To Search▲

Price & Availability of NCP584HSN30T1G

	To Download NCP584HSN30T1G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .